Acrylic Fish breeding Box, Acrylic Fish Isolation Box, Fish Separator for Aquarium, Hatchery Incubator with Suction Cups for Small Baby Fishes Shrimp Clownfish Guppy (3.9 * 3.9 * 3.9inch)

I like the simplicity, size, and it's pretty durable though I'm not sure how long the rubber bands will hold before they deteriorate in the water. The holes and slots are all evenly cut and well machined, I don't see the same issue others are stating saying that the edges are not finished, it's fine the way it is. Sure the edges could be polished smooth but it's unnecessary. And the holes don't have sharp edges, it's just acrylic dust that can easily be rinsed off. Directions are not that great, but I didn't end up using it anyways. However, it would be nice if the directions mentioned what the screws are for (and how to attach the hangers, though it's pretty self explanatory), almost threw out the hangers not realizing they were in the box since the paper on the acrylic is the same color as the box. Turns out the screws are for the hangers!! Hangers aren't wide enough for my rimmed 125 gallon, but it will work for most tanks. Paper peels off relatively easily if you go slowly, it should come off mostly in one chunk. I appreciated that the paper was left on so the acrylic doesn't scuff during transport. The acrylic thickness is just fine, actually thicker than most commercial breeder boxes so I don't really see it breaking without (accidental) force. Overall good value for the money and water flow is decent. Originally purchased for my angelfish fry, but I'm not 100% sure if the holes are small enough so the fry will not come through or get stuck so I'll wait a few days for them to get a little bigger. Couple of tips for buyers: -Peel backing off slowly and it should come off easily -rinse off all pieces as there will be acrylic dust -suction cup works better if you screw the knob after pressing into the tank's surface. Loosen knob to remove suction from tank surface. Not sure if this was meant to be this way but I find it works best to tighten to hold suction, loosen slightly to unlatch suction. Similar to bathroom accessories. Tips for manufacturer/seller: -Better directions, include how to use the hanger. I see there's a video on the product page, but perhaps a link/QR code for a video online would be good or refer buyers to the product page on the instructions sheet. -Remove acrylic dust before packaging, there's a lot, it's a health hazard and gets all over. -Knob for suction cup has space where small fish can get stuck in back, would be nice to have this closed off or a solid piece. -latch of some sort for the top door would make this product even better. Overall great product and I don't really have any complaints. Simple, serves it's purpose, and is nice to look at.

This box is sturdy and the perfect size to isolate a sick fish. Very handy to have. A little tricky to put together but once it is assembled you will love it.

Easy to assemble and works great as an Anemone isolation box. I think it would benefit from a second magnet though as just one makes it unstable and hard to keep straight up and down as it turns easily with only one magnet.

To start, as described, the product comes unassembled. I hate the paper that comes over plexiglass as it's always difficult to peel, but that's what you get for using plexiglass and isn't the vendor's fault. If they took the paper off themselves, it could be scratched or more easily broken in transit. Assembled wasn't challenging for me, but I am also use to assemble Legos. There's a nice diagram that comes with so you know how to align the cube. Be sure to use the bands after you put the pieces together to keep it intact. The suction cup is pretty powerful. I put the box where I wanted, twisted the screw on the inside, and couldn't even slide the suction cup afterwards. The holes in the sides are tiny, but the holes on the lid are much bigger, which brings me to my only want with this product. I wish the side pieces that hold it to the wall of the aquarium let the box slide up higher. I keep my aquarium pretty filled, so the box was completely submerged and the fry were able to escape from the top. Wasn't the huge deal for me, but anyone who's not giving a full inch of head room at the top may want to consider this.

Comes with this film on all the pieces that was a pain to take off. Paper directions that came with it are not even of the item included. Had to watch the amazon video tutorial for how to assemble.