AP Products Devcon 20445 Flow-Mix 5-Minute Epoxy - 14 ml

Epoxy comes with a wonderful variety of properties today. Take the time to understand those properties and you will have great success. This is an amazingly convenient product packages in a slick, self mixing applicator. It can fix some thing fast in an emergency or bond 2 pieces quickly enough so that you can hold them with your fingers instead of clamping them. Good- Convenience Clip off the end, twist on the mixing spout and push the plunger. That is all. Fully mixed epoxy right where you want it. I had a situation where the outer layer of the laminated skin on an RV had come unglued in a small area under an access hole. Stick in the nozzle push the plunger. Wiggle it a bit to spread and hold it together with a gloved palm while drinking some Iced Tea. Mission accomplished. Good- Fast dry. See above. Repair done fast. Although full strength will hot happen for an hour it will hold the pieces together with five minutes. That five minutes was just enough to let it run down and spread around before starting to dry. Good- This is a very runny epoxy. See above. It was liquid enough to get down in the spaces I needed it to before setting. Bad- This is a very runny epoxy. When I tried to use it to fill screw holes in the same situation it ran back out or dribbled down the inside if the hole and did not do any filling. In this situation a more Gell like product is better. Bad- This stuff sets fast. If you have more than one thing you need to glue you may be better off with a slower epoxy. The stuff will set in the mixing tube if you don't keep it moving and although there are two tubes with it it takes about a quarter of the product to fill the mixing tube so it is best to use it in one go. Ugly- You get a half ounce with this. Since you will leave a quarter of it in the mixing tube this is extremely expensive compared to getting a larger container and mixing it yourself. Robs recommendation: Think about what you want. If you want a quick shot of liquid epoxy with clean hands and no preparation then go for it. I liked it so much I got another kit to keep in the RV for emergencies. On the other hand if you want more than a quarter oz, something a little thicker to stay where you put it or a little bit of working time then pick a different one. If you use enough to make it worthwhile you might want separate gel and hardener with optional thickener (check a hardware or boat store or website)

This is a good product and I liked using it. Be aware with these two part epoxies, the more you mix at once the faster they set up. 5 minutes is the best scenario so have everything ready and don’t mix up any more than you need to.

10 minutes NOT 5 minutes, The glue is perfect for repairing my son’s action figures. Crazy glue just wasn’t doing it but this stuff really does the job. they need to add more mixing tubes.

Use to use this when it came in two (2) separate tubes that had to be combined and then mixed/blended together. This new (to me) Flow Mix was so easy and apparently precise as to "equal parts" being dispensed because the results were great! PS: I still blended the mixture a bit on some wax paper the applied to my project with a small spatula (old habits are so hard to break for me - LOL!).

02-13-25 - Another Follow-up - "It Just gets worse". Even after successfully struggling to get the resealable cap on both sides of the glue dispenser, now after four months, one of the two epoxy portions is too hard to squeeze from the dispenser. One of two of these I bought is unopen, and I may just give it to someone I do not like and move onto some other product. Sadly, Devcon used to be a great brand of epoxy. I used it for years until it became harder to find locally. No longer any good. 10-28-24 - Follow-Up: Everything below still applies. The dispenser "system" SUCKS!!! That is, this would work better if there were simply two tubes with separate caps. Again, the glue holds. It's just a poor system of dispensing. PROS: Glue itself seems to hold well enough for my lighter duty needs. CONS: The "packaging", including the mixing nozzles and "snap-on cap", is pretty lame. As mentioned by another reviewer, unless a person has a big job, don't bother with the nozzles. More glue is wasted in them than is used for most small jobs. Also, the "snap-on cap" is hidden in the plungers, though I did eventually find it by accident. Once I had found it, it was a fiasco getting it to seat and seal the glue ports. CONCLUSIONS/RECOMMENDATIONS: I bought two of these packs of glue and will use them, but I would not order them again. The packaging of this epoxy glue in side-by-side cylinders is just not very handy to use, and the mixing nozzles and snap-on cap are cumbersome at best. I would NOT RECOMMEND this product due to its packaging failures.

This works great repairing RC Planes.

This is the best but unfortunately I never received this product

This epoxy works great but unless you have a big job to do, don't buy this particular item. It comes with 2 spiral nozzles which mix the epoxy perfectly, but when done you have to throw the nozzle away. After your 2nd use, then what? Mix it by hand I guess. A lot of epoxy is wasted that's left in the nozzle. This is definitely not for small jobs. I do love it because it does what I bought it for, but this particular item can be a waste of money if all you have are small jobs once in awhile.