Multifunctional Resin 3D Printer Enclosure with Ventilation Filter, High Quality 3D Printer Vented Enclosure Tent Cover Eliminate Odors Compatible with Anycubic Elegoo Series LCD Resin UV 3D Printer

Needed an enclosure for my 3D printer and this one did the job for my ELEGOO Mars 5 Ultra. It comes with an exhaust fan and tubing to push out the fumes. The fan is strong and a bit loud but thats to be expected when you’re working with 3D printing. Definitely locks the temperature inside the enclosure. The design, fit and assembly is exactly what you need for a small enclosure and was super easy and straightforward to work with. Definitely worth the money, would totally recommend.

Like the title says, this is super easy to set up and looks very sharp. It has cut the noise and smell of my printer way down. I barely hear the printer now and only get a very faint smell from it, my husband can't smell anything at all. There is also plenty of space inside it and we have the Mars4 printer. I was worried about it because of the price but it was worth it. Now I know my printer is protected and I also like how the zippers go all down the front side and open up the entire top so getting the printer in was no problem at all. Very nice cover.

I bought this to contain my Saturn Elegoo Saturn 4 Ultra. I needed an enclosure to help with fumes while I was staying in a 1 bedroom apartment. I was surprised by how effective it is. Fumes are very well contained. It was easy to set up, survived one move since I bought it, and makes it easy to access my printer with hinged lid. In fact, I typically leave the printers lid open, with a drip tray installed, and can still easily close the enclosure. My only negative points are that the fan can be annoying (high pitched, whining noise), and that the hose lacks a good mechanism for mounting the exhaust to a window (I ended up using duct tape).

Great for my resin printer. I love this enclosure. The only complaint would be to have a little more powerful fan to pull the fumes out a little better. The fan works well, just wish it were a little more powerful. That's more of a personal preference rather than a fault of the product itself. Otherwise, this is perfection. Absolutley love it and use it all the time with the resin printer.

I am very new to 3d printing and bought this item not realizing that it would not work with my printer so I reluctantly returned it after trying to figure out a way to keep it. It is a very high quality item, all the parts and pieces were present ( even had some extra) and it was easy for a newbie to assemble. My only advice is to measure your printer carefully and consider ease of changing filament before you select a model. Five star item and return was processed quickly without issue. Highly recommend this product and supplier.

Works great. When I stand right next to the printer I don't smell anything.

The enclosure material seems to be alright. I had to use a saw to cut the scaffolding poles to fit into the shell. The one star is for the poor instructions and a zipper end ripped open on one side which makes it impossible to seal and was extraordinarily frustrating. The fan appears to be powerful enough for the size of the enclosure. The filter however is completely useless because when you attach it to the fan when building the enclosure, it obstruct the spinning of the blades. I got this for an Elegoo Satun 16k resin printer and I will say that it fits. However, the USB sticking out of the side might pose a problem and you may have to move your printer around before and after your prints because there is not enough room to open the printer and do your business.

Fits my phrozen Sonic Mini 8K S which measures 11.4 x 11.4 x 16.9 inches perfectly with some room to spare all around it. Plenty of space to take lid off and put lid on, and I have room to insert my USB drive on the side of my printer and can comfortably reach to the back of my printer to turn it on and off with ease. The fan + hose is a game changer! Resin fumes extraction is ABSOLUTELY VITAL!!! Do not skip fumes extraction. This setup has everything you need to accomplish such except for connecting it to a window or wherever you wish to extract the fumes. You can get window inserts for super cheap on Amazon and the hose is long enough. I bought a silicon mat and lined the bottom of my enclosure although it's not required at all...just extra protection to help keep your tent safe in case of any spills. This entire setup is superb quality in every imaginable way! WOW! BUY IT NOW!!! You will not regret it!!!

Tenía mis dudas sobre si eliminaría el olor lo suficiente, pero ha superado mis expectativas. Lo he puesto al lado de una ventana para que el extractor vaya hacia fuera y va sin problemas. Muy recomendable.

Rien à dire, le montage est un peu moins facile que décrit mais reste simple. L'évacuation reste suffisante à condition bien entendu d'avoir une sortie vers l'extérieur. Il y a bien un petit filtre en charbon fourni mais il reste insuffisant pour éliminer les odeurs. Il faut vraiment une évacuation . Le petit ventilateur pourrait être aidé par un extracteur fixé sur la sortie.

SMALL ENCLOSURE: Lightweight, but made with heavy-duty, durable, tear/scratch and water resistant materials (Think anglers' net-bags, rod holdalls etc) The framework is made up of lengths of solid and sturdy plastic (I think polypropylene) which is able to withstand a bit of bending during assembly or whilst being moved/used/adjusted/accidentally leant on) Once assembled, and in use, it is not truly airtight, thanks to the holes for the electrical cables etc, but it is plenty good enough, with the fan-assisted venting, to contain heavy fumes and allow them to be vented outside via the provided fan and tubing. The 'door' or 'window' flap stops short of the 'ground' meaning that the heavy fumes will sink to the bottom of the enclosure and remain in a 'puddle', behind the strip of material across the bottom of the 'doorway' if the fan is switched off. Whilst the fan isn't powerful, and I haven't done a comparison test, it should do a better job than none at all. Having said that, I will be connecting a far more powerful 6in diameter fan to the tent instead. Meanwhile, the 3 inch ventilation tube, is, I think extremely good, tougher than most and with an internal silver-coloured metallic material lining and I connected this to my larger fan using a 'reducer connection'. I left the original fan in place and sometimes use just that to vent fumes as it is quieter. During printing though, I use my large fan and switch the provided fan off. There is no point switching the provided fan on and trying to enhance the airflow using my large fan as well, because the smaller fan can only shift a smaller volume of air than my large fan and will therefore actually impede the airflow to my large fan. The slight criticism I do have of the enclosure itself, for those using a printer around the size of the Elegoo Saturn2 is that the provided fan and vent area is right beside where the USB port is located on the printer, and, if you have an Elegoo heater fitted to the back, one has to pull the printer far enough forwards to allow the power cable around the back of the machine, and for your hand to reach around to switch the heater on or off. And one more issue is that with the 'door/window fully open one has to struggle to lift the Saturn's cover up and over the the printer's Z rails post AND THEN through the top of the 'tent frame' itself. This should be easier with practice, but maybe think about fixing a lifting handle to the top of your machine's cover? If not, perhaps it's a good idea NOT to place your enclosure on a shelf any higher than your waist. LARGE ENCLOSURE. Again, made from good quality materials, nice stitching, etc, if only slightly different with the framework made up of metal tubing instead of solid plastic. And that is the only 'problem' with this enclosure. I read a review a year or so ago, where someone said one of the tubes has the hole drilled in the wrong end and therefore cannot be fitted at all, UNLESS one drills out a new hole at the correct end. And that exact same issue still arises all this time later. So, either there's a large batch of enclosures with the same mistake which still haven't all been sold, and they aren't aware of it, or they are aware of it OR and haven't bothered sorting it out. That aside, it's no big deal to drill a new hole, and once assembled the enclosure is excellent. In fact, it's better than the small one as it comes not just with the fan, but with an LED strip light, a temperature gauge, a hanger for the extractor hose, and some cable ties for the er... cables. With it being double the size of the smaller enclosure, there's less of an issue with space. I have an Anycubic Photon M3 Max and an Elegoo Saturn 2, and I did wonder if both would fit in. Google AI said no, the M3 Max won't fit in when the spare bottle is added to the back of the machine, and the printer is placed in normally, BUT it will fit in sideways. So I purchased the enclosure and thought I'd make do with the awkward set-up. But as it turns out the M3 Max WILL fit in 'normally' even with the spare bottle of resin fixed to the back, so I ended up putting the M3 Max in one side and the Anycubic Wash and Go station in the other. So, I don't stink the room out with IPA so much any more! And I was amazed, and very pleased to discover that the enclosure is actually tall enough to allow one to lift the cover off the Wash and Go station and tilt it towards you and slide it out without even having to fully unzip the 'roof' of the enclosure! And if that wasn't a surprise enough, it's also possible to do the same with the front cover of the M3 Max! And finally, access to all the required cables, USB ports is easy, and whilst changing the resin bottle on the M3 Max isn't a breeze, it's not a hard job either. So, I've got my Saturn 2 in the small enclosure (the printer I use the most) and the Max and Wash Station in the large. And I've connected the ventilation hose from the smaller to the larger and from the larger to the vent to the outside, and with my large fan on I can vent both enclosures at the same time, or just use the supplied fan in the larger enclosure to vent both enclosures at a slower, quieter pace (such as after all the printing and washing has been done and I just want to get rid of the last of the fumes. All in all, a pair of excellent products that offer versatility and make life a lot more comfortable and healthy.

Do drukarki A1 Mini jest akurat jak dodrukujemy top holder, głośny wentylator aaale coś kosztem czegoś.

Muy eficiente, solo le cambié el ventilador de 12v para más potencia, funciona bien, aisla sonido, temperatura y sobre todo los olores, le quedó bien a una anycubic m5s pro