2 Sets Resistive Soil Moisture Meter, Icstation Soil Hygrometer Sensor Test Kit with Corrosion Resistant Probe, Digital Analog Signal Output for Arduino Garden Plant Care Automatic Watering System

This product does what it says. I is easy to use to detect the moisture condition in plant soil, either to set off an alarm, turn on automatic watering, or display an analog moisture value using an Arduino or purpose-built circuitry. The down side is, that using a DC current to measure moisture drives an electrolytic action between the probes. Long-term, this can cause surface erosion and deposits on the electrodes, which degrades resistance measurements, making automatic monitoring or watering control problematic. There are several ways to overcome this: 1: Insert the probe only briefly for measurement, then remove and wipe off before the next measurement. 2: Arrange to swap probe polarity frequently, via a reversible plug, DPDT switch, relay, or similar. 3:Change your Resistance measuring method to use (Floating) Alternating Current instead of Direct Current - this requires more elaborate electronics but should enable long-term unattended monitoring. As a fun project or occasional tool, this device is handy. Quality is good enough to make a long-term automated system, if some modifications are made.

In today’s world of microcontrollers, there have been many inventions and designs concerning the communication over a Wi-Fi network between 2 or more gadgets. Since the appearance of the ESP8266, the Wi-Fi communication between 2 (or more) µC has never been easier. **(search for esp8266 and smartphone)** it will give information and a basic example of the NodeMCU-version of the ESP866 . All pieces necessary are available on Amazon. This wonderful piece of technology can be easily programmed in the Arduino IDE and works together with the Blynk-software. To understand and make use of it, I assume you need the basic knowledge of the Arduino µC & Arduino IDE. This purchase came with 2 of the soil moisture sensors. They can be controlled (monitored) by an esp8266 wifi microcontroller. This in turn can control your irrigation system. Using amicrocontroller, makes it extremely flexible whether you just want to keep the indications local (imagine 3 LEDs one red one yellow, and one green) that you set for each point on a defined scale. Or with the ESP 8266 to your smart phone to let you know it has reached the level. Investigate ESP8266 and smartphone for any code help

Good quality that wont corrode over time. Was easy to use once you figure out how to use it. There is no instructions on connecting to Arduino module through Analog or exactly what the adjustment pot does. Both mine was also missing the plastic tubes that is supposed to water-proof it.. The description shows pictures and clearly says it has "Two Transparent rubber sleeves to prevent water from entering..." - these rubber sleeves are not present and missing. Also once, integrated, there is heavy drift on the readings over time.. it takes at least 5-10 minutes to reach a stable reading, so if you turn the probe off in between readings, its very inaccurate.

Used these as part of a project to automate my garden irrigation this grow season. The readings were nearly as accurate after ~6 months in soil, with no cleaning of the probes. They key is to NOT keep power applied 24/7. I only checked soil moisture a few times a week, giving them about an hour for the measurement to settle after applying power. So, I only ran these for a few hours a week.

This really works well, and is simple to connect. The only issue is finding code to work. You can Google a bit, but I needed something that worked on a Pico which has limited modules. I did find this tutorial which worked perfectly: If you Google: micropython Capacitive Soil Moisture Sensor You will find the tutorial I used.

After soldering the connector, it works pretty good with damp fingers. If it doesn't work well in the soil I will change the review.

I was hopping the bad reviews were just simply users who didnt know how to setup the sensors code. But I tried in Arduino IDE on ESP32/ESP8266/RPi/Arduino Mega and UNO... and also tried to code in ESPHOME in Home Assistant. Issue was I could not get any real reading..... I would get a good reading when I turned the power on, and then every second, it would go up and up and up to where is bassicly the same reading as the bars touching... I tested in cup of water, a cup of potting soil and flooding it/slowly pouring water in the moisten the soil, etc.... But I could not use it... I didnt want to use the PBC sensors as PCB's and putting in moist soil forever, does not last long at all.. so I'm back to the begining trying to get to measure the moisture in my garden for my automated watering that I would like to water on and off based on soil moisture

Overall seems to work. I put the probe in water, dialed the pots down, still got 102%. The manual basically says you're on you're own past wiring. The digital output is limited, but analog is fine. After a few days, I went from 85% to 75% and hovered around there. I'll update in a few weeks if anything unexpected occurs