Lowenergie Occupancy Sensor 360 degree PIR Motion Light Switch Ceiling Mounted 1200w max

Brought this for utility room as the wife was fed up with fighting Google lights to turn on it works really well you can set it to how long you want it to stay on

Bought and fitted a few days ago, after deciphering a few decades of mismatched wires (not the sensors fault) I managed to get it working as intended Been working fine since, it's very sensitive, our bathroom is at the top of the stairs and with the door open it activavtes around half way up the stairs! (this is adjustable) Lux sensor for daylight sensing so doesn't activate during sufficient light, again adjustable along with duration I've found it's a constant motion sensor so for a bath or shower, aslong as your moving now and then it will stay on Red and green led to show it's powered but not active, or active Altogether a good little unit so far and will probably buy more for other rooms in time 4 stars due to it being something I wouldn't recommend trying if you don't know what your doing.. And it being new I can't judge longevity as yet

it does require a neutral connection (the BLUE wire) but it is not an issue as all lights at my house has a neutral wire. I leave the switch on and use the wire after switch to power up the sensor. Then I tune the timer to lowest so I can adjust daylight off by the SENS dial. Once it is set, I then adjust the timer to the time needed. It does require trail and error to find out when the light will be turned off. I find it not linear at all. Moving it clockwise by 1-2 min (imagine the dial is a clock) will change the time from 5 sec to 1 min. I just set it up and hopefully it lasts.

Installation was easy and the product worked fine for about 6 weeks, but then stopped working. The only contact for the seller is a web form, which i have filled in asking for a repair or replacement however i have had no reply. Very disappointing

This little device solved a very impractical problem that I've put up with for years. My dinning room has a door in opposite corners, but only one has the light switch next to it. This resulted in me having to make at least one journey every night in the dark. This was never rectified, due to having to rewire the circuit by taking up the floor above the dinning room and cutting a channel into the wall. This device which was connected via the light celling rose, allows the circuit to be left on. The light automatically comes on and turns off after no movement is detected. There are 3 settings to adjust for sensitivity, the amount of ambient light before activating and duration the light stays on after no movement is detected. The unit looks no more out of place than a smoke detector. The only issue was for my installation, I had to extend the wires slightly. Also the compartment for the terminal block is a little tight. It serves the purpose of being energy efficient when nobody is in the room, and for me it means no more walking into the table or tripping over something I have left on the floor.

Bought this to make the lights under the stairs turn on when someone opens the door. It works great, now people don't need to fumble behind coats to turn the light on which is great. The instructions are really simple to follow so any competent DIYer should be able to install this without a problem. Build wise, the unit seems decent enough, my only comment is that it would be nice to have a side entry for the cable as I had to hide the cables in the wall and bring it through the back but I knew that at purchase.

I would not recommend for a bathroom environment, I probably cannot fault the sensor too much, it worked great for 12 months, but started to stay on because the contacts stuck together, the only way to turn of was to give it a few sharp hits with my long shoe horn. Its now replaced by a different model, I may try to use this in a non damp environment. Also beware to fit this you need to provide an extra cable from the light fittings location so the unit can have its own permanent live power source separate to the light and then provide power to the light with its live and neutral via the switch, you may need an electrician if you cannot work out the logic for wiring this, it is simple once you work it out. Please don't use what I've written its not a wiring guide.

Burnt in a few months . Only used for one LED light bulb

After few weeks it starts turning on and off without detecting nothing. Rubish and no refund

Il rapporto tra il costo e la qualità è rispettato, consigliato. Estremamente facile da montare e per il momento stabile