Fix-A-Floor + Micro Adapter Bottles

Happy to give 5 stars as product has worked perfectly and I have no loose tiles or crunchy sounds underneath after use. I had a phenomenon called tile tenting happen and it fixed it for us. But I will say and warn others that it doesn’t work like in the videos where you squeeze into one hole and it comes up another when filled - this didn’t happen so you need to work out your own system like I did. The solution is incredibly runny (although it needs to be to recess under damaged tiles) but as it takes a while to sink into the holes I drilled, its very easy to over fill them and make a mess until I got into a rhythm. I found it best to work on a section of holes at a time and slowly release the fix-a-floor into the first hole and as soon as it fills up release the pressure on your cork gun and quickly aim the nozzle into a nearby hole as it will drip solution after releasing the trigger on the gun. Squirt, fill, release, aim nozzle into next hole, squeeze, release and next hole and repeat. After a while I got pretty good at it and hardly had any excess mess. Another tip, whilst in periods of rest (waiting for glue to recess) is to lay the gun and aim the nozzle over a hole so if it drips it doesn’t get wasted. I did find some of the holes wouldn’t fill up and not take much solution whereas others were like endless pits so use these ones to catch the excess drips. I also carefully stood / put pressure on the tiles to help the solution squish under them and I could see the air bubbles form in the glue holes and then I could add more solution. Wipe any spills away with a wet sponge and make sure to leave for 24h. I also weighted the tiles with dumbbells. The process is slow and repetitive but works if you follow the steps I did. Have read others say it doesn’t work and is glorified PVA glue but it sets really solid and has to be runny to work correctly.

Very good stuff. Couple of tips - it’s messy make sure you have cloths. Once you have drilled the injection holes, make sure to hoover them out otherwise the nozzle will immediately block. Drill two holes, one for injection and another to release air. Fill the area until it comes out the air hole. Give it good time to dry without being walked out.

Newly installed tile was moving and making noise when I stepped on it. I could see movement in the corner of the tile. The grout has also cracked. I decided to give fix-a-floor a try before deciding to remove the entire tile something which I was not looking forward to. The movement has gone and so has the noise. I would recommend you buy extra needles just in case. Also, when applying, makes sure you have tissue and floor wipes at hand. Also, lay out a black bin bag to act as a work station. The stuff will drip everywhere if you're not careful.

I didn’t like this product. It leaked everywhere when applying, out of the nozzle and the back of the tube, and it unfortunately didn’t fix my loose tile. I wouldn’t recommend it.

I was a bit dubious about how much success I would have with this product, but I was pleasantly surprised at how good it was. I had to remove most of the grout and so a couple of tiles became loose and I had to remove them. No problem though. I just poured some of the adhesive onto the floor and pressed the tiles back into place. Having placed heavy objects onto the tiles afterwards and waited 24 hours they both were nice and secure. I re-grouted the tiles and now there is no movement at all. I wish all DIY jobs ended this way! The thin thin nozzle was an inspired addition as not all the gaps between the tiles were uniform, so I did use this for some of the tiles. The solution is very runny so make sure you hold it vertically when not in use. The plastic cap was also very useful when using the plastic end. A great product and I would definitely recommend. It saved me a lot of time and hassle.

⭐️⭐️⭐️⭐️⭐️ Surprisingly Effective – Saved Me Replacing Tiles! I had a couple of hollow/loose tiles driving me mad and was gearing up for a messy replacement job. Decided to give this a try first and honestly, I’m glad I did. The micro-injector tip makes it really easy to get adhesive exactly where you need it – especially on narrow grout lines. The product is quite runny, so take your time and keep a damp cloth handy, but once you get going it’s very straightforward. I injected slowly, gave it time to settle, then repeated, and it filled the void perfectly. After curing, the tiles feel rock solid again and the hollow sound has completely gone. Much cheaper and cleaner than ripping tiles up, and a great little kit to have for future repairs. If you’ve got a few “clacky” tiles or creaky flooring, this is definitely worth trying before calling a tiler. Highly recommend – saved me time, hassle, and money. 👌

Bad quality tube. I squeezed not so hard and the adhesive came out from the back. I don't know if there was enough adhesive that went under the floor. However, the squeak is gone ...

Worked perfectly. I had a kitchen floor tile which start to 'pop' after being down for around 8 years. As mentioned, the adhesive starts to leak as soon as the top is cut off. After drilling several holes and vaccuming them, I masked the grout edges with masking tape and covered tiles with newspaper. Filling the holes was easy and dried clear after 24 hours. Since re-grouting all is fine.

Ho comprato questo prodotto perché ho delle piastrelle che suonano vuoto e si muovono leggermente. A causa di questo movimento, tra alcune piastrelle lo stucco è mancante, ho comunque seguito le istruzioni facendo un foro nella fuga con il trapano ma, dopo circa 1 1/2 ero riuscito a iniettare pochissimo prodotto e la maggiorparte era fuoriuscito dalla parte anteriore filetto/penta e dal pistone/pistone. Ho consumato anche parecchia carta per tamponare tutto il prodotto che gocciolava dall'erogare anche se imprimevo pressione con la pistola. Farò un ulteriore prova nei prossimi giorni ma, credo che procederò alla restituzione del prodotto che non mi sembra adatto per questo tipo di applicazione.

Instalé suelo LVT en cocina, salón y baño porque me aseguraron que resistía la humedad y no se rayaba. Eso es cierto, pero al año las juntas de la cocina empezaron a levantarse y, con el uso, algunas incluso se rompieron. El problema se agravaba porque debajo había baldosas de barro mal niveladas, aunque me habían asegurado que no pasaba nada. El instalador no quiso hacerse responsable, así que tuve que buscar una solución por mi cuenta. Probé este producto inyectándolo bajo las lamas y el resultado fue excelente. El método que utilizo es sencillo pero requiere paciencia: hago un agujerito con taladro (del tamaño de la aguja del cartucho) en cada esquina de la junta levantada, aspiro polvo y virutas, y aplico lentamente tres pulsaciones de pistola en cada agujero (unos 10 ml por pulsación). Como el producto es muy líquido, es importante mantener la pistola siempre hacia arriba, tapar la aguja con el dedo al moverla y sacar la aguja despacio para evitar fugas. Después tapono con un poco de cera de ortodoncia y celo. El producto se distribuye bajo la junta y entre las lamas colindantes, creando una buena superficie de adhesión. Para que quede perfecto, pongo encima un libro grande que cubra bien la zona y, sobre él, dos garrafas de 5 litros de agua. Así la junta se aplana, el producto rellena huecos y fija incluso pestañas rotas. Lo dejo 4 días secando con peso. Han pasado dos años desde que lo apliqué en la cocina y sigue perfecta. Ahora estoy repitiendo el tratamiento en el salón y el baño, porque aunque el suelo allí estaba mejor nivelado (cemento), también están levantando algunas juntas y noto que las lamas se comban hacia arriba por los laterales. Una vez fijadas, el suelo queda mucho más estable y duradero. Este producto me parece una maravilla: no es una simple cola blanca, es muy adhesivo y algo elástico, lo que le permite adaptarse a pequeños movimientos de contracción y dilatación. Lo recomiendo totalmente para reparar este tipo de problemas. Eso sí: lo que no recomiendo es el propio suelo. Resiste humedad y arañazos (tengo un border collie que corre y derrapa sin dejar marcas), pero las juntas son un desastre. Con este producto al menos he conseguido salvarlo.