DJI Part28 Phantom 2 Series 9-Inch Prop Guards (White)

Trust me on this one, many have said its a MUST, it is. I crashed several times already and my props ended up with some green tree markings and some scuff, but still are 100% fine. I purchased these red and green little caps to make them easily removable. THE guards screw into the caps (not the copter) and then the caps with guards attached snap into place on the phantom. One one terrible crash into a high tree the impact knocked the attachment piece/guard right off. I just snapped it back on and ready to go again. Also recommend either the plexiglass shield or carbon fiber shield that protects the camera and gimbal. I cracked one already, and seller sending another free. MY camera and gimbal never got the impact, the guard did. AND finally, use the bottom part (cut) off plastic hanger and tie wrap it to the skids, worked perfectly- wont ever tip over now when landing!!! Acts as bigger skids, poke it out in the front about two additional inches and leave the back stick out about 5 inches. Not in cameras view, worked great!

These prop guards saved my Phantom , I guess my depth perception , and not knowing the direction my copter was going , I managed to set 2 prop guards on the 35,000 volt lines about 600 ' away and survive without killing it , without the guards it would have come down . If you are an idiot like me and get to close to it running , you will appreciate them . Keep in mind it won't fit in their custom $200.00 case , but I'll bet you can find a bigger and maybe better one cheaper . I may be an idiot , but this is the coolest copter ( and this is number 9 for me ) , I've killed the previous 8 , that other than my high voltage wire balancing act have not crashed (yet) , I can even land it , and that is important .

Here's what I'd say... If you're going to be flying through trees and other obstacles at low altitudes, I'd recommend these. However, if you're mostly flying in open space and high altitudes, don't get these. They install simply enough and protect the props, but... some people say they increase turbulence under the props which can cause instability for the drone. On my 1st flight with these, my drone fell out of the sky. However, that could've been due to a firmware update that wasn't installed yet or any other number of things, so *take this with a grain of salt*, but yeah, the one and only time i used them it dropped like a rock.

They serve their purpose and are very durable, but you won't use them much. I bought these to prevent rotor damage to my quadcopter (DJI Phantom 2) while learning to fly it. Well, learning to fly it was incredibly easy. After the first hour, I saw no use in keeping them on, however, I did for another couple of flights. Only complaint I have about the guards is that it significantly affects how you can transport it. If you own a molded plastic case, it won't fit. If you transport it in your car, you would need nearly double the space you would need without the rotors on. Just take them off to transport, you say? That's all you, buddy. That's 10 minutes I would rather spend flying the thing. Now, if DJI would only make the drone as sturdy as these. My Phantom 2 had a microchip spontaneously melt upon start-up. It is currently at their facility being repaired. No, I never crashed it, nor tinkered with it - the microchip just caught fire and melted. LUCKILY, it was on the ground (during start-up) when it happened, so it still looks brand new. Just hope it doesn't happen again when I get it back. If it does, let's hope it happens while on the ground again.

I received my Phantom 2 less that a week ago. I've flown it on about 10 occasions since then and these prop guards have saved my Phantom's props countless times already. The most common safeguard they provide is when the Phantom 2 lands, it often tips partly over with its props still running. Without the prop guards, the prop blades would collide violently with the ground and likely be damaged. With the prop guards mounted, just the guards tap the ground and the props are untouched. I've also had a few more violent crashes and, again, the prop guards have perfectly protected the props. A gust of wind came up and I lost control of the Phantom 2 about 20 feet up. It fell HARD to the ground, yet there was no damage whatsoever to the props and the guards did not "snap" as I feared they might. (Yes, I should know better than to fly in the wind!) For a novice "pilot" like me, these are the best investment I could've made to safeguard the props from my newbie miscues. Highly recommended.

The prop guards work beautifully and are easy to install. They will definitely protect the props and the vehicle itself if it were to tip over upon landing and in the event the drone were to come into contact with a building or other object. The only reason I rated it a 4 star was due to the fact that with the guards on, the drone will not fit into the custom Phantom 2 case I bought without removing the guards. Perhaps the special cases have been reduced in size. Anyway, it's a good product and worth the investment.

These official DJI prop guards are excellent. Perfect fit for the larger blades on the Phantom 2 Vision & Phantom Vision+. Whether you're worried about chewing up blades as the phantom tips over during a not-so-soft landing, are worried about blades bumping into a tree, wall or building, or you just want an easier way to carry your Phantom to/from launch locations, these are great. I used Krylon Fusion spray paint on the front two guards so that I could easily tell front from rear and they look awesome... I know that the LED's help, but it's nice to have several visual indicators. UPDATE: Great for use indoors, when just learning how to fly, or to make large crowds of people feel a bit "safer"...Avoid using them in windy conditions, or descending too quickly with these attached.

Die Anbringung ist sehr einfach und der Copter wird dadurch natürlich nochmal richtig vergrössert!!! Das sollte bedacht werden, auch wegen dem Transport! Weil mal eben abmachen ist leider nicht, da jeder schutz, mit 2 Motorenschrauben befestigt wird und diese ständig rein und raus zu drehen, ist sicher auf Dauer nicht gesund. Ich finde, der Copter sieht damit nochmals schöner und beeindruckender aus , natürlich schützen die original Teile die Propeller bestens und ich kann sie nur empfehlen.

It protect any armature from having to replace blades after any crash landing , which could be costly and frustrating after a few time of crash landing.

Ottimo sistema di protezione avanzato delle eliche da urti ed ostacoli (e da un utilizzo incauto che qualche utente meno esperto o particolarmente maldestro e distratto potrebbe portare a rischi di danni su esseri viventi ed oggetti), prodotto direttamente da DJI e distribuito da Amazon. La qualità del prodotto originale si percepisce sin dal packaging e dalla modalità di confezionamento. ATTENZIONE! La confezione riporta la dicitura per Phantom 2, ma è compatibile su qualsiasi versione del successivo Phantom 3, che ha lo stesso sistema di viti per l'installazione. All'interno vi è il manuale "sintetico" in inglese e in cinese, oltre alla garanzia e alle avvertenze, che contraddistinguono la professionalità del marchio dagli accessori compatibili. Il montaggio richiede un po' di pazienza e di accuratezza nel maneggiare i materiali, tra le viti, la chiave a brugola e il filo per rinforzare la protezione del velivolo. Una volta installato, può operare in ogni luogo, a discrezione delle norme vigenti e delle disposizioni ricevute. Consegna Amazon Prime al top anche con Poste Italiane!

Everything

墜落破損のため、予備として購入しました、純正品で取り付けも何の問題はありません。