LD-0220-50SC Pair of Soft-Close Pivot Hinges

Felt compelled to write review as this product is abundantly better than the set I bought from Menards. With that said, let me first say the instructions included with these were nearly useless, and were quickly discarded. Before my review, here's my written installation tutorial: ------------------ INSTALLATION: Hardware eventually attaches to both the drawer front and the face frame (assuming you have a face frame cabinet); the order in which they are installed does not matter. These instructions will mostly be for attaching to the frame first. 1) with drawer front panel still installed (or aligned to desired location), use pencil to lightly mark the perimeter on the front of the face frame. [If installing hardware on the drawer front first, from the inside of the cabinet, trace the interior perimeter of the face frame onto the back of the drawer front panel.] Now remove drawer front panel. 2) take the two pieces of tilt hardware, and denote which one is L and which one is R. Take one and place it on the appropriate side of the face frame. Align it so that the bottom is resting on the face frame, and the front is flush with the front of the face frame. With a pencil, trace the locations of two mounting holes (you can use any two) onto the frame. NOTE: I recommend not using holes that are ~too~ close to the top or bottom edges of the face frame, as this will make drilling difficult/inaccurate. Repeat the same process for the other side. 3) Drill (with 3/32 drill bit) the two holes into the face frame. Attach hardware with screws into these holes (I believe instructions called for the provided flathead screws; though I discarded and used my own hardware). Repeat for other side. A 90° drill/driver attachment is useful for this step 4) once hardware is mounted to the face frame, place drawer front panel against the face frame in the desired location (using your previously traced perimeter). From the inside of the cabinet (I did it by feel as I'm not the most flexible) mark the mounting hole locations from the hardware onto the drawer front panel. Remove panel and ~carefully~ drill (3/32 bit) the mounting holes. BE SURE NOT TO DRILL ALL THE WAY THROUGH PANEL (drill bit stop collar is helpful here). 5) install drawer front panel to the hardware. This can be tricky, but can be done either from the inside of the cabinet with the hardware 'closed,' or from the outside of the cabinet with the hardware 'open' though the angle may present challenges. Tip: do not fully tighten screws until all four are in place. 6) test function. You may have to slightly loosen the screws and nudge the panel over to get it to close flush or evenly. ----------------------------- Review: Great product, as stated previously. However, installation can obviously present some challenges due to the tight angles and fairly tight installation tolerances. Lack of helpful instructions can further exacerbate these challenges for many other buyers. Functionally, these are incredibly smooth and close with the right amount of force. Compared to the previous set (different brand) that I had installed, these are night-and-day difference in terms of smoothness. Also for the fact that the previous set SLAMMED shut to the point where it would make a good impromptu nutcracker. I still rate this product as 5-stars due to the great functionality, though engineering improvements to ease installation would be a good place for the manufacturer to focus in the future.

First, the hinges function very well and allow for a simple nudge to close versus holding the pull throughout its closure to prevent it from snapping close and spilling the tray's contents. While these hinges are not critical in people's lives, they are a nice touch, and they motivate household members--especially children--to actually use the tip-out drawer and tray. Regarding installation, one should immediately compare these hinges to their scissor-hinges already in place. For me, every exterior dimension was the same except for the presence of the soft-close piston which was irrelevant, and most importantly, the size and location of the two mounting plates--to the frame and the back of the drawer panel--were the same size and location. Of the four utilized mounting holes on each hinge--two facing the interior frame and two facing the back of the drawer--three matched exactly. Only the lower mounting hole of the plate to be attached to the back of the panel did not match, and consequently, a new mounting hole only in the back of the drawer panel needed to be created. As a result, all I needed to do was: 1. With the drawer fully opened, I used a cordless screwdriver to back out the two screws attached to the frame for each hinge 2. After removing the drawer completely, and with the drawer flipped and exposing the old hinges while placed on the kitchen island, I used masking tape to locate the exterior edges of the mounting plate and hinge assembly 3. I removed the old hinges and placed the new hinges on the backside of the drawer panel at the exact location of the old as dictated by the masking tape and mounting holes of the plate. I then used a marker to mark the new location of the lower mounting hole and then drilled a 1/8" pilot hole. 4. After screwing in and attaching the mounting plate of each hinge to the back of the drawer, I pulled to open each hinge fully to its lock position, placed the drawer and hinges in the frame opening, and screwed in the mounting plate of each hinge to the frame using the existing mounting holes. The hinges worked perfectly, and the drawer was positioned in the exact same location as before. Comparing dimensions and mounting hole locations of old versus new hinges is worthwhile and may allow for easy replacement as above. Early DIYers can accomplish this, and they should not be afraid to dive in. Good luck!

The hinges worked fine. I like the soft close over earlier versions of the product without soft close. As other reviewers have mentioned, the hinges came without directions or templates. I installed the hinges on the side openings of the cupboard aligned with the front edge and about 3/32” above the bottom. My guess is they would have worked just fine set right on the bottom. The panel for the opening for this particular cupboard happened to be screwed in place originally. So, to locate where to put the hinge screws on the panel, I screwed the panel back in place. Then I laid down on my back in the cupboard and took a pencil and marked the hinge holes on the panel. I then unscrewed the panel, removed the hinges from the sides of the opening, screwed the hinges to the panel using the pencil outlines of the holes I just marked. I then hen re-screwed the hinges back on to the sides of the openings. This was a little awkward and a second person to help hold the panel would be helpful. (Note that I had to remove the hinges from the sites of the opening so I could get clearance to attach the hinges to the panel.)

Totally outstanding product, clearly thought through from beginning to end. Even my carpenter commented on the quality of the build and how gently (but tightly) the soft-close feature works. These brackets allow the drawer front to tip out pretty far, which is great for me -- it's about 5" from the top of the drawer when tilted out to the face of the cabinet, which feel really roomy. Nicely done, Rev-A-Shelf!!

Our new house had the original Rev-A-Shelf tip out hinges with the exposed springs, but they were not in good condition (rusty and stretched out of shape). I was excited because the pilot holes were already there for the new soft close hinges, i.e. no measuring or calculating where to put the hinges in the first place. However, even with the pilot holes it was mildly difficult to get everything screwed into place. For the first drawer I installed the shelf with the hinges to the base cabinet first. Then tried putting on the interior cubby and attaching a handle to the outside of the tip out drawer. This way was the most difficult as it was hard to get leverage with the screw driver (even using an Allen wrench style Phillips head). I tried climbing into the cabinet, lacing my arm up and through, you name it. But it’s difficult with the sink blocking your arm. After many swear words later I proceeded onto the second shelf. This time I attached the hinges, screws for the interior cubby and drilled the holes for the outer handle before attaching the whole thing to the sink cabinet. Then, I needed someone to hold the shelf at the appropriate tip out so I could screw it all onto the base cabinet. This worked WAY better. Have a look-see at the new tip out shelf (with new paint job as well). The hinges open and close nicely. I noticed some people mentioning that the shelf doesn’t shut fully...if you just press it a bit it will close completely. I am very satisfied!

Quality hinge

I bought 2 sets of these hinges for 2 separate drawers in a bathroom vanity. They were installed identically, but I can't make one side of one drawer front close completely. I swapped hinges and the suspect hinge still won't close completely even on the other side, so the problem definitely seems to be a issue with that hinge. There were no instructions included with the hinges, so I was left with YouTube and searching online. There doesn't appear to be a practical way to increase spring tension, which I think would solve the problem.

I am a bit of a quality nut and built my own cabinets, so I wanted a high end hinge. I looked around a while at the big box stores, even online for these. Most hinges clang shut, don't open well, having movement or play and failing to close softly. These looked pretty good so I gave them a shot. It does not disappoint Great finish, nice motion and keeps the drawer front perfectly square. Soft close works well. depending on situation, you may have to get a plastic bumper to to on the faceframe of the cabinet where the bottom corner meets. When you open it, it does hit the faceframe, not hard, but I can see it potentional showing a mark after much usage. No matter, the bumper will be hidden when closed, so if that is all I have to complain about, then fine. In all, the quality is top notch and if I do this same think on other sinks, I will purchase this in a heartbeat. It is the best I have seen. Very easy install if you have raw cabinets, but I can appreciate it would be more difficult once you have a slab of granite on top. it does have quite a few mounting holes, so seems to be a bit flexible for multiple applications.

Il est de bonne qualité

Amazing item to use on the blank space under the sink now I have a functioning unit that surprises everyone that sees it

It’s a good idea. But a template that lined up would be a good start point at This price! And some basic instructions as well ! Like mark inside of draw 1st, 2nd mark bottom of draw on cabinets so you know where to place hinges, 3rd pilot hole and screw test depth! 4th only put 1-2 screws in & test positions !

I disliked that it did not have the templates that were supposed to be included and ti was expensive. I liked that it worked as advertised so it is worth the expense.

This part was a perfect replacement for the existing hinge that "slammed" shut...it was very easy to swap out the parts and works great.