HCW-11

I bought this tool as well for my bike this is the third time I bought another tool for my bike because there’s different types of nuts the tool works great

Tool inside measurements are 16mm x 35mm. Good for vintage bikes! I used this to remove a seized vintage Raleigh bottom bracket cup. Use “the bolt trick” to help remove a stuck one. Bolt trick instructions: (or Google it, lots of people use this) Parts list: 1 bolt, 1 nut, 2 large washers, park tool wrench, a hammer. (Whenever you use a hammer on a bike, make sure your ball bearings are removed. If not possible, be aware you may damage parts. The hammer taps in this method need to be just the weight of the hammer, no added force. Be patient.) 1. Measure your axel hole and bottom bracket length for your bolt size. Measure bottom bracket diameter for the washer size. Get a bolt that fits in your axel hole with some wiggle room, get it as close as you can, and plenty long. I used a 5/8” x 6” bolt. Cheap digital calipers are good enough for stuff like this. 2. Get washers that are as wide or a little wider than the diameter of your bottom bracket. 3. Set up your bolt trick: put first washer against the bike, put the bolt through. On the other side put the second washer against the bike then screw the nut on, leaving about a centimeter of space. 4. Now slip in the wrench onto the bike, with your second washer on top, followed by the nut. 5. Tighten the nut carefully to keep the wrench in place. You may have to use two wrenches to hold the bolt. I had to use needle nose pliers on the end side of the bolt. That’s ok, it’s not supposed to be super tight. Just lightly snug. 6. Tighten nut until wrench is able to be held in place. *Gently* tap the wrench with a hammer. Once it slightly moves, loosen the nut a little to allow space for the bottom bracket cup to come out. Tap tap tap. Once it moves again, loosen nut again. Finally, loosen nut completely once you can use the wrench by hand without the hammer. Usually it just takes a couple little taps to break that initial seal. Seized cup tips: PB Blaster was not strong enough for a 50 year old stuck part. I soaked my bottom bracket cup in a 50/50 mixture of acetone and Automatic Transmission Fluid. I would not do this on a frame you want to keep perfect, as the mixture can potentially damage your paint and metal. Watch it carefully and clean up any drips. Wear gloves and goggles and have drip pans ready. To soak it, angle the bike so that the fluid will flow out of the bottom bracket, not down the other tubes. Have drip pans ready anyway. And have a soapy wet towel to wipe up spills on your frame. That seemed to help me. I put the bike problem-cup side down, then took soaked pieces of paper towel and poked it into the bottom bracket shell with a tool. Making sure the paper towels come above the cup inside the bike. Regularly check on it and regularly pour more mixture into the paper towels. You can reuse the mixture that drains out of the bottom. I did this for 2-3 days. Good luck!

This is a solid tool from a great vendor. Got here five days early. So no complaints about it. That said, if you are a little shocked that fixing a wobbly crank is going to take four different $16.00 single-use tools, I’ll tell you that you probably don’t need this one. The pin spanner on the HCW-4 will work on recessed notch cups, and a regular adjustable wrench will take care of the raised wrench fittings. Up to you. Sometimes it’s nice to have exactly the right tool. But if you don’t want to drop another $16.00 on a single-use tool, this is the one you can skip.

Not very good for ajustable cups that are tight or seized,the tool starts bending and marring,not a very good design,shame on you park tool!!!

I TIED DISASSEMBLING MY BIKE WITHOUT THIS TOOL WHICH WAS A FRUITLESS UNDERTAKING . FOR A ONE TIME DEAL THIS IS AN EXPENSIVE TOOL. THE POSITIVE SIDE, WITH THE ADDITION OF A BOLT AND WASHERS TO HOLD THIS TOOL IN PLACE IT CAME APART EASILY. I REALLY LIKE THIS TOOL ALTHOUGH I'LL NEVER USE IT AGAIN AS THIS BIKE IS A 1961 MODEL AND HAD NEVER BEEN SERVICED.

If you can get the other end off, then unscrew the BB from that end, It's often easier too, Then a simple arrangement of a long bolt and some nuts/washers can be use to clamp this ring and screw it out. Left hand thread on Raleigh bikes, If it's really tight, the Parke Tool needs to be clamped on amd doesn't have the torque force of the other method. I kept it anyway, It's a good tool when the disk is loosened.

Perfect tool for adjusting the bottom bracket on a 30 plus year old bicycle. Happy to be able to get one.

Have an older style tandem bike. Every blue moon the front cranks start to work loosen; have use this tool to tighten them back down. This tool does that job.

I bought this to remove an old style bottom bracket that had essentially welded itself to the bike. I must have hit this thing with a hammer approximately 1000 times and it stood up to the job very well. Glad I didn't buy a cheaper alternative. Very impressed. I got it off in the end if you were wondering! :-)

Macht was es soll! Stabil.

Title.

excelente calidad de acero, me permite hacer bien los ajustes necesarios para la reparación de bicicletas

Muy práctica para el mantenimiento de bicicletas.