IP65 Waterproof Junction Box with Fixed Ear

Exactly the product I needed. Quality material, sturdy and it looks great. Good price.

Worked perfectly for what I needed

Good quality materials and accurate description of dimensions means these fit perfect for what I needed. Tip: Holes drilled with a stepped drill bit turned out perfect with the density of the plastic where the first hole I drilled with a normal bit walked around a little on the surface.

I bought this with the intention of mounting a printed circuit board (PCB) in the bottom. It will work for that purpose with some minor modifications. My only complaint is that that mounting holes are not the same height. There are 6 mounting holes in the box... 4 in the corners and 2 in the center. The 2 center holes are a few millimeters higher than the ones on the edges, so trying to get a PCB to sit flat is going to take either some shimming or cutting. Would be nice if all 6 holes were the same height from the get-go. Other than that, it appears well built and I have no doubts it will keep water and weather out!

I used one of these to create a waterproof switch box for our outdoor cat shelter's heated floor. The ample size gave me plenty of room for what I needed, which was just space for 2 switches and the main power entry point. The included pre-drilled holes/mounting points are a welcome touch as well. There are numerous spots inside for stand-offs or mounting items inside, although I didn't utilize any of them. Being made of ABS, it will obviously be brittle, but working with care, you can easily avoid any accidental cracks/breakage. I used a combination of my drill and dremel to cut out the openings for the 2 power switches and the actual power cable's female port. The seal/gasket material that is included was more than enough, and I've found that as long as you tighten everything down EVENLY, it creates a very good seal.

I bought the "Junction Box, Zulkit Project Box Waterproof Dustproof IP65 Universal Electrical Boxes Enclosure with Fixed Ear Black 4.5 x 3.5 x 2.2 inch (115 x 90 x 55 mm)(Pack of 1)" Bought this to house a LED wireless controller attached to my spa. I needed the box to be outside of the spa because of where the low power was installed and length requirements of the low voltage wiring to LEDs. Anyway, this box did the trick. I drilled 2 holes for the wiring on the bottom and used grommets. The generic LED controller (one of these cheap small china made controllers) fit nicely in it. I put the cover on with the supplied rubber spline for the seal. The box has a little channel to insert the spline. You want to make sure you install it correctly and not leave any gaps. The supplied strews were nice as well. As you see from the attached picture, this box sees plenty of water. From rain and the spa itself. I open the box the other day and it was bone dry. Perfect. The box itself feels solid and sturdy. For under $10, it's does the job. We'll see over time if the seal holds and if the box fades at all. Only been a few months.

Very good box! Best quality and great price. Thanks

This year I wanted to line the sidewalk up to my house with a string of RGB smart Christmas lights. I put each light on a stake that pushes into the dirt and aligns level with the sidewalk. However, the length of my sidewalk was such that I had to buy a longer string of lights than I had sidewalk, so I had about 17 extra lights that had nowhere to go. So I purchased caps where I could remove the bulbs and cap off the sockets - mistake. I should have removed the bulbs BEFORE I purchased the caps and would have noticed that the light itself is not part of the bulb. The bulbs are just caps themselves, the light is built into the socket and cannot be removed. So I returned the caps and wondered how I could solve this. I thought that maybe a waterproof box where I could hide the extra 17 lights inside would work so ordered this. This box is plastic, a rectangular shape with no holes on the top or sides except for the screw holes. It comes with a piece of elastic gasket that you can easily insert into a groove on the edges to help keep it waterproof when the top is screwed on. I checked to see that the 17 lights would fit and seeing that they would, I then drilled a 1" hole into the side of the box with a spade bit (very easy) then fed the 17 lights/bulbs into the box. I screwed on the lid and hid the box in the grass next to the last lit bulb on the sidewalk. Because it's black, one can hardly see it. There's still the issue of the hole in the box where I fed the lights being open to the elements or bugs climbing in, but I plan to use a gasket or waterproof tape to block that off. When I remove the lights after the season is over, these 17 will just stay in the box, ready for next year. This box worked great for my Christmas light needs - especially because I was doing a sidewalk, so I could hide the box in the grass. If I were doing a roof line and had extra lights it might be a challenge to hide the box but I guess it's not impossible. Nevertheless, this turned out to be a great solution to having too many lights on the line.

Satisfait

Awesome

Exactly want we wanted. a strong waterproof box.

I had four 12 VAC 50 watt halogen lamps with fried transformers. I found these floor lamps to be quite elegant and versatile for reading etc. The lamp design used the metallic lamp body as the conductor (allowed at 12 V). Anyway, I used these junction boxes to house 15 watt 12V DC transformers and replaced the 50 watt Type G4 base halogen bulbs with 5 watt G4 LED bulbs. They all work very well and are at least as bright as the old halogen bulbs which also had the disadvantage of becoming hot enough to burn if the lamp head is touched - the LEDs barely get above blood temperature. This indoor application does not require moisture resistance which may account for the price of these junction boxes. However, they serve the purpose very well, housing the transformers and providing strain relief.

All very good but cannot keep the seal in place. I will pack it with silicon grease instead.