CRJ Micro 4-Pin GPU Dual Fan Adapter Cable - 6-Inch (15cm), Black Sleeved - Micro PH (2.0mm) PWM Graphics Card Fan Adapter for Connecting Two 3-Pin & 4-Pin PC Fans

Have been waiting to try and hook up a small PMW fan to my series s just to see how it would work. The fan header on Xbox series X/S’s is a 4pin micro GPU style plug. The CJR splitter works perfectly but I did have to cut the end off one of my noctua 4pin fan extensions and solder the male end to the stock series s fan so I could simply plug into the CJR splitter, went with a noctua 40x10mm PMW cooling fan for this set up and the series s has no issues powering stock exhaust fan and the noctua fan! No usb wires ran all over the exterior, noctua fan starts, revs up, revs down and shuts off as stock fan does with the PMW controls. Was a bit tricky getting the splitter and extra wires tucked into mobo shell but got it and have two 3-4 hour gaming sessions down with no issues. The CJR splitter is very good quality, sturdy plugs and all pins were nice and secure on all ends. Would buy again and recommend!

Works as expected, runs a full 120mm fan without any issues

When my Zotac 1080mini started to make fan noise, I found I wasnt alone. My thoughts were to add it into my water loop and be done, but the cost was just not worth what buying two 92mm fans and a small franchise on cable-ties. Super happy to find that a cable like this already exists, which speaks to the population who do actually repair their own VGA cards. Its a very cheap ($30ish) to effectively make your card quieter and cooler which might have a positive impact on performance. The Amazon review for this asks me how warm, thick and sheer this item is, and I can wholeheartedly say that its just fabulous for all three.

Some things are intended to be simple and just work. This is one of them. I have had zero issue using this alongside (2) 92mm Arctic fans for a custom solution cooling my GPU. Look no further for this type of adapter.

So I got this so I could put my identical noctua pwm fans on the gpu heatsink and after a simple installation, come to find that the 3 pin on the splitter doesn't work. The fan plugged into the 4 pin in the splitter spins, but that's only half the cooling at puts my gpu capped off at 91c in games. Even after switching the cable on the two fans to make sure for some reason my fans went bad, got the same result. So I'm at a loss. Wanted to use these fans, but guess I need to dig through my closet to scrounge some up until they both work.

I have an RX 580 GPU that goes thru it's OEM style fans about every 8-9 months. I got tired of hunting down replacements and wanted to just ziptie some 92mm case fans on it, but I didn't want to ruin the 'factory wiring' on either the 92mm fans or the cards wiring harness. This allowed me to do that. The two 92mm fans plug right into this harness and the small 'micro gpu' end plugs right into the GPU circuit board. It actually runs cooler _AND_ quieter now. Now when I eventually go to sell the GPU, I can slap the factory shroud w/factory style fans back on the cooler and it should be good to go. Actually, this worked out so well I will need at least another one to keep on hand.

After my second round of ordering since the first order somehow got damaged in transit to me and ended up being returned to amazon it functions.

I've used 2x of these in different manufacturers conversions... SOLID construction, exactly as described and works amazing.

Natürlich ist der Preis viel zu hoch. Aber im Gegensatz zum Konkurrenzprodukt für 6€ von Gelid rutschen die Lüfter Kabel nicht von selber wieder raus. (Noctua Redux in meinem Fall).

Added a fan to a fanless mini PC.

La verdad me ha servido mucho, ideal para tarjeta gráficas no actuales, hay que conectarlo a la tarjeta ya qué esta regula los ventiladores del sistema liquido, que esa fue la actualización qué hice a mi tarjeta rx 590

Basically what I said in the title. I bought this adapter cable to slap some large fans onto my graphics card, and this allowed me to use the mini fan header on the card. Job done.

Used this when I deshrouded my graphics card. Works really well and good quality too.