EBOOT Mini MP1584EN DC-DC Buck Converter Adjustable Power Module 24V to 12V 9V 5V 3V(6 Pack)

Excellent adjustable buck style voltage regulators.. don't get hot, provide a soild voltage feed with raises and falls that stay within 1 to 2 hundredths a volt.. give a fairly clean output voltage (still need a LC filter if you want very clean wave forms) provides 0.6 to 23 volts from my testing.. able to pull a constant 3.5 amps off it at 16.8v without it getting hot 2.5amps at 20volts gets warm but ok... 3amps at 20v will cook the coil in about 20 minutes.. at 12v I was able to pull a solid 4.2a off it for 2 hours and the temp never got above 97F, 4.5a at 12v smoked it in 7 minutes... If you cook the coil on it it does NOT allow full voltage to pass through (I have had some buck regs fail and allow full voltage to pass through for a few seconds.. I killed two of these intentionally to make sure that when it failed no voltage pass through and on neither one did that happen and that makes me VERY HAPPY. A failure acts like a breaker, it fails it fails and circuit is instantly broken.. I tested this with a O-scope and it had 0ms of full voltage seep when it failed..) These are incredibly cheap and excellent quality.. over preform and stay dang steady.. These are without a doubt the best cost to preformance ratio bucks you can buy... Bucks are not a place to skimp and buy as cheap as possible BECAUSE a failure on a buck that is supplying constant regulated voltage to high dollar electronics and fail and allow unregulated voltage to seep by for even a 1ms can damage sensitive to voltage electronics and ruin your day and make you wish you wouldn't have saved that 30 cents per piece.

I used this to reduce the speed of a 24V fan, making it nearly silent. I snipped the fan wires and soldered them onto this board, then taped it down. Turned on the fan and adjusted the screw until it was the right balance of airflow and noise. Overall, works really well and price is great.

It worked great when I tested one of them. So I permanently glued it to my setup. And now the potentiometer is not changing the voltage on 3 of them. I am pretty sure I didn’t turn it too far but who knows maybe I applied too much force. So just be gentle I guess. Giving it 1 star because the product was great when it worked. But didn’t even last a few seconds of adjustments. EDIT: I changed my mind. They are working really good now. Yeah the potentiometer can be finicky but it works. By trial and error you can get the right voltage. Just be careful to go really slow and gentle while changing voltage. Don’t push down too hard and turn slowly.

I bought the 3-pack of these MP1584EN buck converter modules, and 2 out of the 3 worked. The one that didn’t work had visible damage: the MP1584EN regulator IC was cracked, and after testing it, I confirmed that the chip was shorting out. I’m not sure if that happened during shipping or before it was packaged, but the other two modules worked fine. For the working ones, they have been good little buck converters. They are very small, which is nice for compact electronics projects where space is limited. The voltage adjustment works well and is very precise, but the potentiometer is sensitive, so it takes small turns to dial in the exact voltage you want. Once adjusted, it held the voltage fine for my use. I also did a quick current test on one module by briefly shorting the output through a multimeter in amps mode, and it showed around 500 mA. That may just be the module’s short-circuit protection kicking in, so I don’t think that means it can only output 500 mA. It may be able to supply more with a proper load that actually draws current instead of a direct short. For my low-power project, though, it was more than enough, and the working modules never really got warm. Overall, I like them. They are small, easy to use, and work well for low-power electronics projects. I’d just recommend testing each one before installing it permanently, especially if you are using them for something important.

Work like a charm. I used them to rewire Christmas village lights. Damn department 47.

I’m an Escape Room owner and have used these many times to reduce 12vdc voltage to 9v, 6v, 4.5v to power different escape room technical props/puzzles. I’ve also used to replace battery operated Halloween props like blow mold pumpkins using a 12v power supply and knocking down the voltage to replace the need for batteries. Cat5 wire or speaker wire works well, in a pinch, to accomplish this. As others have mentioned, adjusting voltage is a bit tedious and requires a small (tiny) screwdriver and it is somewhat hard to dial in, but it works with a little patience. Make sure your input power and polarity is correct or you will fire the circuit board. I tend to use a large heat shrink tube to enclose/protect the circuit board after hooking things up.

Device oscillated when turned on with 2 to 5 volt output swings at 1 kHz. Set pot to middle (which was likely the original setting) and same. Soldered in another and it was the same. Watched output while turning the pot and device works great when pot is set for output below 4.5 volts with 5 volt input. Pot at middle is outside the working range for 5 volt input. Hope this saves others some time and frustration.

These are fake converters. They all output a static voltage that is barely lower than the input. The potentiometer is fake. There is no ability to adjust it. The actual screw that should exist doesn't. There is just a small metal cover that looks like a philips head screw. If you look at it with a microscope, you can see that there is a small shaft underneath, but nothing attached to it. It looks like the potentiometers are all just broken. This was the case on all 6 that I received and match reports in other reviews / videos for this part.

I got these to power a raspberry pi on my 3d printer. it was really simple to set it to 5.3v out on 24v in and it gets warm but not to a concerning level. voltage seems steady. Seems to be working great! cant wait to use the other 5 somewhere

As described. Works perfectly.

It had the right pin pitch for a breadboard and the pot could be adjusted to get the right output voltage.

This device is small and adjustable to any voltage within the range specified, not just the discrete voltages listed. ie you don't select a voltage from a finite set of choices, you adjust it to anything you want in the range. Once set, it doesn't matter what the input voltage is, so long as it's within the specified range. At 3A rated output, it's perfect for mobile application payloads (eg. on drones), instrumentation platforms, and so on to name a few. At the low cost these devices sell for, I'm going to buy another batch just to have them around for those last minute projects that need a great stable power supply.

I used this buck converter to convert a set of solar LED string lights to run off the 12v battery in my tent camper. I simply connected it to a spare 12v battery on my bench to set the output to 3.5v before shrink-wraping and installing it by splicing into the existing exterior light circuit on the trailer. I was concerned that a higher input voltage while charging the trailer battery may effect the output voltage but it does not. Steady 3.5v regardless of input voltage. I will report back on dependability and heat generation after I've run them for an extended time in a few weeks.