HVAC Heater Blend Door Actuator, Compatible with Toyota Camry 2007-2017, Avalon 2005-2016, Highlander 2010-2016, Sienna 2011-2016, Venza & Lexus ES350, ES300h, RX350 - Replaces 8710607120

Item worked as advertised. Other purchase never worked until I got this one. Put the two attaching screws loosely so that the planetary gear engagement nob portion can be moved to click match the correct portion on the actuator and then tighten the screws to fix in place. Then, clip the power connector to the actuator. Had to wait five minutes or so after installation of actuator before restarting the car for the automatic temperature control to actually work (maybe a due to reset cycle time??). Short stubby phillips screw driver and portable light source will help. Best.

This was a perfect fit for my 2014 Toyota Sienna LE. Solved the problem that I thought was an A/C issue in the summer and a heating issue this fall. Maybe my A/C unit isn't leaking after all and maybe the blend door actuator was just not diverting AC from the right spot because the actuator motor was dead. It is pretty awkward to get to it, but removing the bottom plastic above the pedals (by your knees) was pretty easy -- I did not totally remove it and only slid it up for better access. I did not disconnect the temperature sensor, so it was easy to put back. Just two 10mm bolts and a few plastic clips.

Fit the bill and didn't cost an arm and a leg. Sidenote: when installing, to line up the teeth... all you have to do is take out the old one, screw the new one in, then push up the white plastic teeth until it clicks in place... It will be aligned just by this, no need to try to line the teeth up (I was paranoid and kept checking) You can confirm by turning the car on and turning the temperature up and down and watching the motion of the actuator and see that the big square tooth in the middle lines up with the cut out. Easy Peasy.... I made it more complicated than it needed to be

The part work for what we needed it for. However it was very hard to get to area in the car to pull the broken one and replace it with this one. The product we received was well made.

We replaced this on our 2010 Toyota Highlander Limited ( drivers side ) The part worked just fine. Better price than the auto parts store and the dealer for sure. There are youtube videos of how to do it yourself. Its pretty simple to do .

Product worked. Misrepresented though. Description says made in USA one of the reasons I bought it. Got it and big sticker on side says made in China.

Symptom: Driver side vents blew HOT even when AC was on Max and the Climate Control system took a full 90 seconds before turning on. It took literally less than 5 minutes to remove the defective unit and install this new one. Just two Phillips screws and one electrical connector. Once installed all functions were returned to normal operation without any type of reset or code clearing required. This is a simple repair that is easily done by a novice. The most difficult part is getting your head in the driver’s footwell to see what you are doing. Perfect, Highly Recommended.

Take a photo of how original is installed before removing it. Notice the odd shape gear on the back of the actuator module (see photo). The wide tooth needs to align with car’s plastic piece (see yellow area of picture. Otherwise the car’s heater door won’t open/close correctly. Take your time think it thru before screwing the new actuator to the car.

Replace the part and work 100% for Toyota sienna 2014

Came next day and worked like a charm. Toyota one looked to be close to 500 dollars for the part. Hopefully this lasts for a little while.

Exactly what was needed and for 1/5 the price.higly recommend for my sienna 2013 v6.wow safe my entire life especially right now it's extremely cold so I needed this part asap.Thank you looking forward doing business again.Hopefylly it's going to last a while.

Fits like oem part, installed in less than 10 min, works perfectly. 1/5 of toyota price

Had nothing but heat on the drivers side of the Venza. Took 10 minutes to change out the part and everything works as it should now. No issues.