3S 4S 12V 5A Battery Active Equalizer BMS Balancer Lipo Li-ion LFP LiFePO4 Lithium Battery Balance Active Energy Transfer Equalization Module Faster Whole Group Capacitor Balancer PCB

I'm sold. These little guys just work. Latest build is a 4S2P 12v LIFEPO4 and the cells have been as much as .20 out of balance while charging. Within a couple hours they are exactly the same. I've read some horror stories with these and the main thing to.prevent problems is to install these before the battery pack is a mess of mismatched voltages.

I found this battery balancer very useful and effective. I used it daily for months, but it died due to my error. Please triple-check the battery pack's resistance. I failed to notice a dead battery with high resistance, and the capacitor exploded and melted my silicone mat. The photo shows the melted area on my mat.

This Active Cell Balancer is great! I had a very unbalanced 12 Volt (3 series) Li-Ion battery pack and it gradually brought all 3 cells to the exact same voltage (within a couple miliVolts of each other). What I really like is that it balances the cells regardless of their voltage or state of charge (unlike the passive resistor cell balancers which only work when the cells reach 4.2 Volts). This is my favorite feature since I only charge my cells to 4.0 Volts (approximately 80% state of charge for long term life). I performed a very careful measurement of the quiescent current and it is less than 10 mA (so no problem for my setup to leave it running continuously). A great product!

Balanced a badly unbalanced 7s3p Li-ion battery in just a couple of hours. Much more effective than resistive balancers.

I’ve been having trouble keeping a custom 140Ah 4S LiFePO4 battery properly balanced. I decided to give this a try and am SO glad I did. Of all the solutions I’ve tried, this one has finally achieved a perfect top balance with all cells at 3.6500 +/- 0.005. It balances at a higher current than most others I’ve used, so is particularly well suited for larger sized setups. It didn’t get hot while working, not even warm to the touch, which is another huge plus since it’s in a closed space in a warm environment. It was running at several amps for an entire day in 90F environment and wasn’t even slightly warm. As an added bonus, it has pads where you can solder on a switch to remotely turn balancing on/off. I use this to disable balancing when battery is not in use, but can flip it on when charging. If you wanted to get fancy, you could even hook up a simple relay to automatically have it turn on with charging and off at rest. At rest, background current draw seems minimal, but I wouldn’t leave it hooked up if storing a pack for several weeks. All around, a FANTASTIC device.

Simple to install. Checked with my clamp meter and it would transfer up to 2 amps on my system. Though it balances more aggressively than a BMS, if batteries are way out of balance I recommend parallel balancing batteries first. I also recommend taping some barley paper over the exposed circuits to prevent short circuits.

Bought four, cheap, 200AH LiFePO4 cells and a Daly 200A Smart BMS from aliexpress. Had one cell that would hit High Volt Disconnect (HVD) (w/BMS set @3.65V/cell) while the others would only average <3.250-3.300. I cleaned, sanded, swabbed, terminals and switched cells around to no avail. The best I could achieve on differential voltages were always >0.150, oftentimes >0.250 when charging at 30-40 amps. A capacity test yielded about 135AH +/-. After installing this active equalizer the cell differential voltages are always <0.010 and are more often than not <0.003. I now have my BMS set at a HVD of 3.60V and easily achieved 175AH (after charging @ 25 to 30 amps) when I quit the test early. I paid almost as much for the BMS as I did for the cells (the cells were actually that cheap). My thinking was that I would upgrade the cells in the near future for my camp trailer. However, the cells arrived well after I sold the trailer. I bought a smaller (energy wise) truck camper and now have no reason to upgrade. I now plan my energy for 175AH and am quite happy with my cheap battery.

I read through the reviews. Some people were having trouble with this equalizer, most reported it to work very well. I'm in that camp. After connecting it up to a 4S2P Lipo that showed one of the packs in the battery was out of balance with the other packs by a fairly good margin. I connected up the equalizer and left it on for two days through mild charging and discharging from my solar panels. The cell packs all came up to with in .01 volt. I powered up some items to draw the batteries down and then recharge them. The cells on the battery that had the balance issue stayed within .03 volt of each other, and once recharged returned to .01 volt difference. Works like a champ.

Connected this balancer to a 6S2P bank of SCIB 20AH LTO cells and after a few hours it had every cell within 2mv of eachother. Unlike other balancers that only balance when near full charge this balancer continues to operate throughout the voltage range so take that into account when choosing the best balancer for your application.

Balanced like a champ for 10 minutes after I got it installed on a 16S LiFePO4 pack. Would be a great unit, if it didn't let the smoke out and stop functioning.

Never got to use it. Maybe it is meant for an experienced user, Other than wiring order, has no information. Does it need to be used with a charger, Does the BMS have to be disconnected ? Do the batteries have to be fully charged ? When should it be used ? It is a new type of balancer (Capacitive) I don't have time to spend looking all over the internet only to see people arguing pros and Cons. I am using Daly Smart BMS, but it has a different plug for the balancer. It would be a good idea to use a standard plug, so you could just unplug the wires from the BMS, and Plug them into this device.

Yo el puso en un pila de 12s y 48v si hace su trabajo