Genmitsu CNC Router Machine PROVerXL 4030 for Wood Metal Acrylic MDF Carving Arts Crafts DIY Design, 3 Axis Milling Cutting Engraving Machine, Working Area 400 x 300 x 110mm (15.7''x11.8''x4.3'')

I was using a 3018 to 3040 converted machine for a couple years, and was absolutely plagued with the amount of play in everything, resulting in chatter and poor tolerances and etc. This unit is SO MUCH more solid than the units that run on tubular rails and move the workpiece up and down on the Y axis. Within the first hour of milling, I had a problem: The power wire to the motor burned. It turned out upon autopsy that one of the leads of the main power wire had been severed inside the insulation (and within the drag chain), probably during manufacture rather than just an hour of operation. That began arcing, the arcing melted the insulation as well as the neighboring wire's insulation, and the two shorted. I contacted SainSmart and they were very responsive, immediately shipped me an entire replacement drag chain assembly and a couple other parts that could have potentially been damaged due to the short, and followed up about how it worked. Definitely very well supported - the exact opposite of the first machine I used. In my opinion, if any one thing could be seriously improved (including by the user), it would be this main power wire. It's maybe 18ga in less-than-flexible insulation, and I would replace that with about 14ga flexible wire in silicone insulation plus an outer jacket. But I haven't had any issues with the replacement wire - I just think that could have been a bit better designed, and could be improved by you in your shop very easily. The drag chain has lots of extra space - mine is now also home to a small poly air line, as well as a 120vAC tool cord for the router, so you can stuff other lines of different types through the drag chain as needed, rather than having them dangling around the work area. If you've never assembled any desktop CNC before, you might think this is a pain to assemble. It's not. I was done in maybe 2 and a half hours. A surprising number of parts actually come pre-assembled, so that you only have to do maybe half or a third of the actual assembly in your own shop. I used a lot of thread locker. I don't know that this is necessary, but the fasteners are going to take a lot of vibration, so it's probably a good idea. It's been a pleasure to use. I've used it with the included 300w 48vDC spindle which is very good, a >1HP router, and a 10w laser. The machine has performed exceedingly well all the time. There's SO much more force in the stepper motors than the little 3018 devices (and the torque clutches have much, much higher thresholds), it makes milling completely different. I've milled soft woods, hard woods, acrylic, and a lot of aluminum on this so far. I expect I could probably mill some mild steel with a good carbide bit and a lot of patience, but I haven't tried that yet. I also added some little cardboard flaps on the left and right sides to keep dust and chip out from under the roller wheels for the Y axis. I don't know if they'd have issues rolling over debris, but it could potentially raise the gantry and mess up your Z axis, so I think it's probably smart to cover those with some dust deflectors.

Unit arrived very well packaged. Easy setup, I suggest using blue loctite on all the screws. I use UGS to run this machine and Carveco Maker for design. The included 300W spindle is okay for engraving but if you want to cut or mill, the upgrade to a bigger motor is a necessity in my opinion. The ProverXL 4030 came with the dewalt dwp611 mount so you automatically save 65 bucks. I also installed the Foxalien remote switch so that the spindle turns on and off automatically. With the much more powerful dewalt motor cutting and milling are quite easy. This is an excellent machine to have if you’re looking to get into CNC work. I’ve had only one issue in about 150 hours of operation so far. I went to home the machine after completing a job and the Z axis failed to stop when the Z up limit switch actuated. I stopped the machine and after some brief troubleshooting determined that the Z limit wire harness had a broken wire. The switches both worked and the controller received the OPEN/CLOSED signal okay. I emailed SainSmart at 3 pm MST with a summary of the issue and by 6 pm I had received a response with an apology and a promise to send a new Z axis limit harness. They were out of stock but said they should be able to send a new wire harness within a week. True to their word they shipped me the new harness at no cost to me and the customer support rep, Joey, kept in touch throughout the process including checking in to insure i had shipping updates and confirmed delivery. Very easy install for the new wire harness and i’m happily back to running my machine. I was disappointed I encountered this failure but the customer support was outstanding. If you’d like to get into CNC routing, you can’t go wrong with the ProverXL 4030. Upgrade the spindle motor and get busy!

The package arrived very quickly, I must see that everything is fine, in a few days I will be assembling the machine and I will update this review, I will give more details and photos. Thank you. Update Well I was able to assemble the machine without problems and it is my first cnc, the manual is very easy, even the software for the G code is also easy to configure, I think it is the best option in quality and price, since other brands are very expensive . Update 02/03/2021 Perhaps these details will help you decide whether to buy this machine or not. The machine works well, it can be improved by increasing the size, since the working area is not very large despite the size of the machine. on the other hand you can put a new router. Now in my case I have had problems with my laptop and apparently the drivers, a compatibility problem and what happens is that the grblcontrol candle software works very slowly, especially if the design has many vectors. Windows 7 or 10. This could be fixed with a simple update I would say. Another problem that I noticed is that the controller of this cnc seems to be sensitive to voltage changes, that is, if someone connects or disconnects an electrical equipment in the house, the machine can stop and the work will have to be thrown away. I clarify this is my experience and perhaps this evaluation will also help the Genmitsu team to improve their cnc equipment.

Buy this if you want to spend the next three hours setting up the machine only to discover it won't work and then you get to spend another 45 minutes disassembling it and repackaging it to be returned. -The drivers don't work (Mac) -The USB stick provided (software and drivers) is type A (large USB) not USB-C so you need an adapter (not included) if you have a Macbook or newer computer. -Cable that connects the computer to the router is also USB-A. Macbook won't recognize device even with an adapter. -The instructions are absurd and just flat out wrong at times (have a look at them, Amazon posts a PDF). -Software programs like Easel aren't compatible. It's just a nightmare all around...

Have had this some years now and just written review. There is a newer version which I can't comment on. But this one works well. Can earn money with it but needs time to learn how to use it.

Ottima CNC molto robusta e semplice da assemblare. Il suo software e molto intuitivo e facile da usare. Un ottimo prodotto molto consigliato.

Muy aguantadora en los errores de operación por mi falta de experiencia. Hay videos tutoriales. Sencilla de armar

De levering was zeer vlot. Er waren wat problemen met het toestel in de eerste dagen. Het contact met support was super en ze doen er dan ook alles aan om het probleem op te lossen. Zelfs nieuwe onderdelen versturen is geen probleem. Genmitsu rules!

La machine de gravure CNC Genmitsu PROVerXL 4030 est une véritable pépite pour les passionnés de gravure et de découpe, offrant des performances exceptionnelles sur une variété de matériaux. Ayant récemment intégré cette machine à mon atelier, je suis émerveillé par ses capacités et sa polyvalence. La première impression est celle de la robustesse de la construction. Le châssis solide et bien conçu assure une stabilité pendant le processus de gravure, réduisant ainsi les vibrations indésirables et garantissant une précision maximale. La taille de travail généreuse de la PROVerXL 4030 offre également une flexibilité appréciable pour travailler sur des projets de différentes tailles. La polyvalence de cette machine est un véritable atout. Sa capacité à travailler sur une gamme de matériaux tels que le bois, le métal, l'acrylique et le MDF en fait un outil adapté à une variété de projets, du simple marquage à des créations artistiques plus complexes. Les résultats sont nets et précis, révélant la qualité supérieure de la gravure. L'intégration du contrôleur GRBL et la compatibilité avec divers logiciels de commande facilitent grandement l'utilisation de la machine. L'interface conviviale permet aux utilisateurs de tous niveaux d'expérience de prendre en main la machine rapidement et de commencer à créer. La PROVerXL 4030 est également dotée de moteurs puissants, permettant des vitesses de gravure et de découpe impressionnantes. Cela, combiné à la précision du système de guidage, offre des résultats rapides sans compromis sur la qualité.