Ademco 5816WMWH White Door/Window Transmitter w/Magnet

Works exactly as I expected. Easy to program and configure with my system. Excellent option when we replaced our entry doors and the installation company cut the wires from the old sensors

As described a worked great with Alarm system Great piece of equipment original manufacturer worked well.

Worked great. Please keep in mind that these are bigger and thicker than other door/window sensors Honeywell has. If you are working with a much smaller installation area, I would recommend the slimmer 5820L or the sleeker 5815. Both are wireless but has a much smaller profile than this one. Especially for windows, I kind of wish I knew about the 5820L. The sensor came with its own double sided tape and installation screws. So depends on where you are mounting it, you can decide which open you want to utilize. I used the sensor and test out different places before installation. Also, keep in mind that you might want to remove the mounting backplate if you are using double sided tape. I found that for windows, the sensor and magnets are in much closer proximity if the back plate for the sensor was removed

Have an old Vista 20P with a 6150RF keypad and had a Window sensor go bad. Picked this 5816 hoping it was compatible and it was! The only issue I had, was that the older 6150 keypads require you to blindly reprogram. So if you have a 6160 you'd be fine, otherwise you're going to have to figure out a way to have someone walk you through the setup (that is no fault of this product). The only downside that I didn't like with this sensor, was I found it extremely difficult to get the cover off. My older sensor you just depressed a tab and they popped right off. This new one was so hard, I basically had to use a screwdriver to pry the cover off. Luckily I won't have to replace the battery for 5 to 10 years :)

our 14-year old alarm sensors are starting to fail... one by one, they trigger the alarm to go off at random times. Rather than having the alarm company come out for $100 per visit, plus the cost of the parts... I just buy these as needed and switch them out. Search youtube for videos with step by step instructions for removing the old sensor and installing the new one in the alarm system. Now that I know how to do it, it takes minutes to replace them. I've replaced 3 so far, and anticipate needing to do more as they continue to fail. Very happy with these so far!

Very easy to install and program—just follow the instructions on YouTube.

This didn’t work at all

I bought this to replace a faulty sensor on my ADT Quick Connect system. Of course, ADT wanted $100+ to send a guy out to punch in the code to activate the new sensor.I asked them to give me instructions on how to setup the new sensor and they refused (because according to them, they have to supply me with one, so they can charge me double or triple what this honeywell 5816 is worth) So this is what you do to replace a sensor. go to http://intellahome.com/alarmpdfs/lynxplusinstall.pdf and download and print this manual. It applies exactly to the quick connect system Then go to your security panel and punch 6321 800 (you should see programming menu on screen..if you do not, stop as your configuration may be different) * (now you should have a blank screen) *56 (this will put you on the zone configuration menu) then type the 2 digit zone number you need to modify Then follow pages 38-41 on the instruction manual Basically you have to delete the serial number of your existing zone, then place the menu on autolearn, and with this new sensor (the lid and battery has to be on) place the magnet on the side of the sensor, You will hear 1 beep. Take the magnet away for a few seconds, and then place it against the sensor again, you will hear a 2nd beep and the serial information will be filled automatically on the screen. Keep pressing * until you get to the next zone #, then press 00 * 99 to exit FYI, this sensor has to be setup in the following configuration on the Quick connect Zone type = 03 (perimeter) should show B03 on screen Report Code = 10 (should show C10 on screen) Input type = 3 (should show D3) If system asks for LOOP NUMBER, use 2 (for the magnet type) or 1 (for the wired type)

Seguridad de cada Excelente producto

Easy to install. Sync in seconds.

works great. No issues since instalation.

Solo incluye la pieza del sensor falta el iman y la imagen muestra que ofrecen las 2 piezas

Pairs with my alarm honeywell panel easily.